Once the screen is all rinsed out, put it back out in the sun to dry and fully harden. DO NOT use a power washer or stiff brush as this may damage the edges of your design. It can help to gently rub the screen with your fingertips or use a gentle spray nozzle. Using cool running water, run the screen under the stream to remove the unexposed emulsion from the screen. Remove the bag, acetate sheet and plastic glass. Once you think your emulsion is properly exposed, re-cover everything with the bag and take it to a sink. If you do over expose the screen use the screen emulsion remover and start again once the screen is clean. That is your sign it is ready! If you are using an exposure bulb, it is generally about 12-14 minutes to expose the emulsion, but every bulb puts out a different wattage so you may want to do a test screen for the first try. Watch the emulsion carefully, it will darken from a yellow green to a blue green. Take the bag off and leave your screen in the sun for about 2 minutes. Pro-Tip: Use a piece of cardboard to help move your screen around before exposing it. Now, if you are going to take it outside cover everything by slipping it in a black plastic bag, you don't want to start exposing the screen until you are outside. Lay the plastic glass over the acetate sheet to hold it down. Lay your printed acetate sheet on the screen or on your exposure bed, be sure to flip it so that when you turn the screen over for printing it reads in the right direction! If you have a good dry screen the sheet should peel off and you can discard it or save it to use for some other craft project. If any emulsion starts to come up then it might not be dry enough, put it back in the dark closet and let it dry. Take out your screen, carefully pick the corner of the plastic carry sheet up from the emulsion and slowly peel it off. Pro-Tip: To make sure you get a good image on the screen, print two acetate sheets and tape them together to get the ink opaque enough. While the screen is drying prepare your image, print it on to the acetate using a copier or laser printer. You do not want any light to be able to get in. Put your screen into a dark box, closet, etc. ![]() One last time press/smooth the emulsion sheet from the back to help it make contact to the screen mesh. Press the emulsion sheet firmly on the screen and smooth it out with a squeegee.įlip the screen over to check for any areas that didn't stick/get wet enough, these areas will be sort of white. ![]() Next, take out the emulsion sheets and peel one off the stack, put the rest back in the package for later.Īpply the sheet to the wetted screen with the shiny side up, it is hard to see in photos but there is a clear shiny side which is the plastic sheet the emulsion is carried on. You don't want it drenched but thoroughly wetted. ![]() Using the spray bottle, wet the back of the screen as evenly as you can. ![]() The photo emulsion sheets are light sensitive so time is of the essence for this part. Make sure you have a dimly lit area to apply the photo emulsion sheet to the screen and a dark location to let it dry before you get started. Airbrushing, Stenciling, & Body Art Supplies.Non-Toxic Markers (Best Markers For Kids).Dyes For Painting on Cotton, Rayon, Linen, & Hemp.You can use Emulsion Remover as is for tough stencils, or you can also dilute it up to 1:4 with water for stripping of easier stencils. Use a high-pressure washer and begin washing your screen from the bottom and work your way upward. Rub your screen with a brush or a non-abrasive scrub pad to make sure emulsion remover is spread evenly over the coated area.ģ. leave for 15-30 seconds.ĭISCLAIMER: If left on longer than the recommended time emulsion can lock permanently on the screen.Ģ. Once you have removed ink from the screen, apply our emulsion remover to both sides of a wet screen. Non-hazardous, safe for all mesh types, our emulsion stripper is a solution for you. It will liquefy your screen almost instantaneously. After applying this to the screen it will begin to dissolve your emulsion allowing for an easy reclaim process. Ready to Use or can be diluted 1:4 with waterĮcotex® Screen Printing Emulsion Remover by Screen Print Direct ® is a powerful emulsion stripper helping increase your speed of reclaiming and screen cleaning.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |